Getting Familiar with Plumbing: The First Step for Bathtub Installation
Getting Familiar with Plumbing: The First Step for Bathtub Installation
Blog Article
We've stumbled on this post relating to How to Install a Bathtub directly below on the web and think it made perfect sense to write about it with you over here.
Mounting a tub isn't specifically rocket science, but it does require solid plumbing, woodworking, and also sometimes, tiling abilities. Changing an old tub with a brand-new one is likewise a moderately challenging task. If the old bathtub is easily available, the task can relocate speedily; if you have to open up a wall to remove the old bathtub and position the brand-new bath tub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly require an assistant to leave the old bathtub and embeded in the brand-new one. Make sure you have qualified on your own for the work and are comfortable attempting it. Rather than working with a specialist to take control of a halfway-completed job, it is much better to think about using one prior to you start. Opportunities are you may require a specialist plumber to make tube connections.
This post will help you set up a new bath tub in your shower room if you have actually currently gotten a brand-new bathtub as well as don't need to transform the setup of your previous supply of water pipes.
Your tools and material list should make up the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, after that the first thing you must do is disconnect the supply of water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The procedure of removing the existing faucets can be fairly troublesome because of the limited accessibility that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will certainly come from the pipes. Once the supply pipes have been eliminated, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning throughout this process. When the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing substance.
Prior to going on to fit the brand-new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the mounting opening in the bath/basin guaranteeing that the washers remain in location in between the faucet as well as the sink. Safeguard the tap in place with the manufacturer given backnut. Once the faucet is firmly in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The former type should be attached to the faucet ends first, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Mounting the Tub
Utilizing both wood boards under its feet, place the bathtub in the called for setting. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four little factors.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by checking the spirit level as well as adjusting the feet on the bathtub up until the level checks out level.
To set up faucets, fit the bottom of the furthest flexible tap connector to the ideal supply pipeline by making a compression sign up with; then do the same for the other tap.
Activate the water supply as well as inspect all joints as well as new pipework for leaks and tighten them if necessary. Fill the bath tub as well as additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
Finally, take care of the bath paneling as defined in the producer's instruction manual. Tiling as well as securing around the bathtub must wait until the bath tub has actually been used at least when as this will certainly settle it into its last position.
Planning for the Installment
To start with, the supporting frame provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the tap features a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps device to stop stress on the bath tub.
Fit the adaptable tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you use all of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its final position.
Tiling Around the Bathtub
In the area where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to crack a stiff seal, causing the water to permeate the wall surface in between the bath as well as the tiling, resulting in problems with dampness and possible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and fittings. They are marketed in tubes and also cartridges, and also can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of drenched paper or soft rope. Remember to always fill the tub with water before securing, to enable the movement experienced when the bathtub is in use. The sealer can split relatively early if you do not take into account this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily available on the market. It is suggested to fit the ceramic tiles using waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed our piece on Tools You Need to Install a New Bathtub . Thank you so much for finding the time to read through our blog. Remember to take a moment to distribute this article if you enjoyed reading it. Thanks a lot for taking the time to read it.
Burst pipes? Get immediate help. Report this page